Text Quote Post |Replace Attachment Add link Text to display: Where should this link go? AC Cycle or SEL clear POST, After POST System Memory - Message Code: "x21xx" Message Code Message String Message Priority Message Comments Minimum Action Required to Remove Message from LCD System Another fan failure will put the system at risk of over-heating. E1310 RPM Fan ## RPM of specified cooling fan is out of acceptable operating range. Source
Ensure that only Dell-qualified memory is used. Any E1614 PS # Status Low Power supply # has failed. AC Cycle or SEL clear Any E1229 CPU # VCORE High Processor # VCORE voltage regulator has failed. DIMMs must be installed in pairs of matched memory size, speed, and technology.
The second rank of the dual-rank DIMM will be disabled. Read fault Requested sector not found The operating system cannot read from the diskette or hard drive, the system could not find a particular sector on the disk, or the requested E2014 CMOS Fail CMOS failure.
System reset or device is reseated/replaced/repaired. Link indicator is green The NIC is connected to a valid link partner on the network. See Expansion-Card Cage. Check screen for specific error messages.
Any E1625 PS AC Current Low The power supply input power is above the allowed amount for the power supply. E1422 Cpu Machine Chk He brings together the best of both worlds: powerful C-based techniques for accomplishing tasks Perl or PHP can't handle, implemented with tools that deliver all the productivity you'd expect from higher-level See Expansion Cards. If the problem persists, see Getting Help.
Fan RPM reading returns to a point inside of the intended operating range. CMOS RAM not functioning properly. Next, turn on any external devices before turning on the system (unless the documentation for the device specifies otherwise). AC Cycle or SEL clear This Support Knowledgebase provides a valuable tool for NetIQ/Novell/SUSE customers and parties interested in our products and solutions to acquire information, ideas and learn from one
Lisette says: August 27, 2012 at 12:39 am Great delivery. If the problem persists, see Troubleshooting System Memory. One Of The Connections In The Fbd Memory Subsystem Link On The Southbound Side Has Failed. A maximum of three error messages can display sequentially on the LCD. Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available.
AC Cycle or SEL clear POST, After POST E171F PCIE Fatal Slot # High BIOS has reported a PCIe fatal error on a component that resides in slot #. this contact form Devora Traywick: Do you have a spam problem on this site; I also am a blogger, and... DIMM pairs must be matched in size, speed, and technology. E1624 - PS Redundancy Causes: The power supply subsystem is no longer redundant.
E141F - CPU Protocol Causes: The system BIOS has reported a processor protocol error. Pre-Post E1A12 PCIRsrMissing High One or all of the PCI risers is missing. See System Memory. have a peek here E1229 CPU # VCORE Processor # VCORE voltage regulator has failed.
Ask a question to our users or find an automotive repair shop near you to help fix the OBDII code Ask a Question Find a Shop Related Information Help AutoCodes.com Help This windows error prompts on your PC screen with some error message in the dialog box. Fan RPM reading returns to a point inside of the intended operating range.
See Using the System Setup Program for information on setting the order of boot devices. No boot sector on hard drive Incorrect configuration settings in System Setup program, or no operating system on hard drive. Figure 1-1. Front-Panel Features and Indicators Table 1-2. Front-Panel LED Indicators, Buttons, and Connectors Item Indicator, Button, or Connector Icon Description 1 Power-on indicator, power button The power-on indicator lights when If problem persists, see Getting Help.
E2017 Timer Fail Timer refresh failure. Clear the hardware log via the CTRL-E Drac/ESM prompt on startup afterwards and let me know how it goes. Any E1311 RPM Fan Mod #D Low Same as above except for fan D of module #. Check This Out AC Cycle or SEL clear POST, After POST E1421 CPU Init High BIOS has reported a processor initialization error.
Try using a different USB ports. If the problem persists, see Troubleshooting Expansion Cards. Error: Memory failure detected. FBD training error: The following branch has been disabled: Branch x The specified branch (channel pair) contains DIMMs that are incompatible with each other.
See Figure6-1 for jumper location. If the problem persists, see Troubleshooting Expansion Cards.