If identified the PCI card failed, replace the PCI Card. Exit system setup and restart the computer. System plugged in, but either turned off or in Windows Hibernation State. 1- Off2- Off3-Solid4- Off - Reserved 1- Off2- Off3- Solid4- Solid Suspend to RAM Windows Standby State. 1- Off2- If available, install a working graphics card into your computer. Source
Otherwise, you may lose data. See "Memory Problems" for additional troubleshooting suggestions. Sound and Speaker Problems Fill out the Diagnostics Checklist as you complete these checks. Okay, unplug the power and open the computer up. more info here
lisa September 7, 2012 what does it mean if the D light is orange???? Check the monitor power light If the power light is lit or blinking, the monitor has power. If you require further assistance, please contact technical Support. Okay, unplug the power and open the computer up.
Hard-disk configuration error The hard drive failed initialization.Run the Dell Diagnostics. greengreengreengreenNormal operating condition after POSTNone. Check the cable connector for bent or broken pins and for damaged or frayed cables. Dell Error Lights 1 2 3 BIOS not execution.
You're on your own. Dell Dimension 4600 Abcd Error Codes We will list a few of the most common here, but there are certainly more on the Dell website. POST diagnostic LED patterns Note: Unless otherwise notes, the power LED will show as solid white/blue/green (depending on the system) to denote a normal power state. find more Dank u.
they look like little colored aluminum cylinders. Dell Error Lights 12 Another failure has occurred. Ensure that the disk is not full or write-protected Ensure that the disk has available space and that it is not write-protected (locked). Press the power button again to restart the computer.
It should also give you a description of the beep codes. https://forums.penny-arcade.com/discussion/62818/dell-not-starting-and-figuring-out-a-b-c-d-error-codes See "Drive Problems" for troubleshooting suggestions. Dell Abcd Error Codes No memory modules were detected. Dell Dimension 2400 Abcd Error Codes If two or more memory modules are installed, remove the modules, then reinstall one module and restart the computer.
Check all card connections in the computer, and reseat any loose cards. this contact form Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available. There's nothing you can do about it except a motherboard replacement. Close the computer cover, reconnect the computer and devices to electrical outlets, and turn them on. Dell Error Lights 2 3 4
Their supplier sold them bum capacitors. So what does this combination ABC=green, D=amber mean for the Dimension 8200 ? If any of the tests fail, contact Dell. have a peek here Ensure that the device is turned on Firmly press the device's power button.
The Diagnostic LEDs remain 1, 2, 3, 4, and placed on the front of the unit. Dell Error Lights 123 Ensure that you have not made an error while entering data See the documentation that came with your program to make sure that the values or characters you are entering are Find the service tag.
LED is blank. CAUTION: Before you begin any of the procedures in this section, follow the "CAUTION: Safety Instructions." Back Panel Diagnostic Light Codes Light pattern Problem Description Suggested Resolution offoffoffoffNormal off condition See "Drive Problems" for troubleshooting suggestions. Dell Error Beep Codes It was a common problem on a lot of Dell desktops of that era.
Check for interrupt request conflicts See "Resolving Software and Hardware Incompatibilities." Network Problems Check the network cable connector Ensure that the network cable is firmly inserted into both the network connector I already checked all the cables inside the machine to make sure they were no loose. Try to resolve the problem Write the beep code down on the Diagnostics Checklist, and perform the action recommended in the following table. Check This Out I am trying to get spare ram and graphics card see if that shed any light.
CAUTION: Before you replace the battery, see "CAUTION: Safety Instructions." Replace the battery If you have to repeatedly reset time and date information after turning on the computer, or if an See your operating system documentation for information on running these utilities. Plug in your computer and reboot it. Here is an example of the online documentation of a Dimension 4600.
Memory data line failure at address, read value expecting value A memory module may be faulty or improperly seated. So any adivce would be greatly appreciated. The error codes mean nothing unless it stays on one. Run the Dell Diagnostics Reboot the computer and run the Dell Diagnostics.
Diskette subsystem reset failed The floppy drive controller may be faulty. I found on google about the A B C D led lights on the back of the computer. solihin October 29, 2012 I have CPU Dell 170L ,the lamp indicator A-B-C-D off but lamp of power is on green ,what happen with my mainboard ? See "Drive Problems" for troubleshooting suggestions.
Replace the memory module(s) (see "Memory" for module installation procedures). No CPU present. Some of them are vague though so come back here with it. See "Memory Problems" for additional troubleshooting suggestions.
Remove all peripheral cards from the PCI and PCI-E slots and restart the computer. If the power light is blinking green The computer is in standby mode.