If you have two or more memory modules installed, remove the modules, reinstall one module, and then restart the computer. If the computer starts normally, reinstall an additional module. S6 STO 3, 3 3 blinks followed by a short pause, 3 blinks, long pause, then repeats No Memory detected If customer can assist to troubleshoot, narrow down the issue by DELL.COM > Community > Support Forums > Desktop > General Hardware > dell optiplex 330 wont boot!!! http://applecountry.net/dell-optiplex/dell-optiplex-745-error-codes-3-4.php
I am thinking it might be the processor, but I am not sure? If the problem persists, contact Dell (see Contacting Dell). Mar 27, 2014 | Dell Precision PC Desktops 1 Answer Optiplex 330 power button blking amber Hello Ricardo,Unfortunately, a blinking amber power light means your power supply has failed. Ensure that the main power cable and front panel cable are securely connected to the system board. https://www.manualslib.com/manual/418671/Dell-Optiplex-330.html?page=56
Ensure that all hard drive and optical drive cables are properly connected to the system board. Computing.Net cannot verify the validity of the statements made on this site. If you can assist to troubleshoot, narrow down the issue by removing one by one the storages on motherboard to determine which one failed.
Meer weergeven Laden... Je kunt deze voorkeur hieronder wijzigen. Toevoegen aan Wil je hier later nog een keer naar kijken? Dell Optiplex Gx270 Error Codes look up the documentation for your computer, and find out what that light error code means.
If only one memory module is installed, try moving it to a different DIMM connector and restart the computer. Dell Optiplex 330 Light Codes Include an image. Log in om deze video toe te voegen aan een afspeellijst. http://www.dell.com/support/article/us/en/04/SLN284978/en Memory modules are detected, but a memory configuration or compatibility error exists.
When the computer starts normally, the patterns or codes on the lights change as the boot process completes. Dell Optiplex Gx280 Error Codes and I don't know where to find it! Blinking Amber Initial State of LED at power up. If the computer boots, add the peripheral cards back one by one until you find the bad one.
dell optiplex 3 lights dell 330 lights dell optiplex 330 problems dell optiplex 330 start lights Related Topics: Dell OptiPlex 330 Desktop... http://www.computing.net/answers/hardware/what-do-the-1-3-4-green-lights-on-the-front/71480.html Stay logged in Sign up now! Dell Optiplex 330 Beep Codes Or just drag it here! Dell Optiplex 755 Error Codes 3 And 4 Autoplay Wanneer autoplay is ingeschakeld, wordt een aanbevolen video automatisch als volgende afgespeeld.
Sudos AbonnerenGeabonneerdAfmelden225225 Laden... http://applecountry.net/dell-optiplex/dell-optiplex-error-codes-3-and-4.php I don't believe the problem you are encountering can be solved in a forum. For more detailed and in-depth help, I hang out at www.suggest-a-fix.com computer help forum (free). this just might go with me to work and have the kids mess with it. Dell Optiplex Error Codes 1 3
This assumption is not correct since you are not considering erratic, i.e. If identified the component failed, replace the component. I have dell optiplex gx 520 running on win xp. http://applecountry.net/dell-optiplex/dell-optiplex-error-codes-2-4.php If available, install working memory of the same type into your computer.
If the operating system is attempting to boot from a device (such as the floppy drive or optical drive), check system setup to ensure the boot sequence is correct for the Dell Optiplex Gx620 Error Codes No memory modules are detected. If the computer has a graphics card, remove the card, reinstall it, and then restart the computer.
If two or more memory modules are installed, remove the modules (see your service manual), then reinstall one module (see your service manual) and restart the computer. If it illuminates, there could be a problem with the system board. Dell OptiPlex GX620 PC Desktop 2 Answers Dell gx270 ethernet controller driver download Dell OptiPlex GX270 PC Desktop 7 Answers Dell GX150 - Power light flashing orange Dell OptiPlex GX150 SF Dell Optiplex Gx520 Error Codes Diagnostic LEDs for the OptiPlex series (Prior to 2005) This series of systems had a block of A, B, C, D LEDs on the back of the chassis that lit up
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. The computer is in a normal on condition. technuba 36.726 weergaven 3:36 How to Repair a DEAD Computer - Duur: 58:55. http://applecountry.net/dell-optiplex/dell-optiplex-330-error-codes-1-3.php Nov 06, 2011 | Dell OptiPlex 330 Desktop Desktop Computer... 1 Answer I installed Windows 7 on the Dell Optiplex 330, normmally it 's working fine.
May 31, 2010 | Dell OptiPlex 330 Desktop Desktop Computer... Contact your technical support to take this further. Table of Contents: Diagnostic LEDs for the OptiPlex series (Prior to 2005) Diagnostic LEDs for the OptiPlex Series (2005 to 2009) Diagnostic LEDs for the OptiPlex series (2009 to 2012) Diagnostic I believe that either one of two things is happening. #1-The power supply is not sending a consistent Power Good Signal, or #2-The motherboard circuitry is not responding correctly to a
Ja Nee Stuur ons feedback Feedback bevat ongeldig teken, speciale tekens die niet worden geaccepteerd zijn <> () \ Feedback verzenden Excuses, ons feedbacksysteem is momenteel offline. If it doesn't contact your technical support If it does add the parts back one at a time until the fault re-occurs, test that part in another slot and contact your You can't post answers that contain an email address. If there is an error message on the screen identifying a problem with a device (such as the floppy drive or hard drive), check the device to make sure it is
Loading... If none of the storage failed, replace the motherboard. Solid Amber The second state of the LED at power up, indicates that the POWER_GOOD signal is active and it is probable that the power supply is fine. Remove the coin cell battery for one minute, reinstall the battery, and restart.
Maybe I will actually try to remove the fans and blow off the dust and reinstall them?