The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various internal tests, and it displays the information in the device list in the left pane of Sorry I don't have more hardware/software info, but I didn't realize I was coming to a computer that wasn't fully booting up. one day when i start my pc. Dell Optiplex 745 comes with diagnostic indicators. Source
Note : Please click on the title of the section you want to open below, in order to see the contents. Back to top #8 gorilakhan gorilakhan Topic Starter Members 6 posts OFFLINE Local time:05:08 AM Posted 02 October 2013 - 04:15 AM Hi Bory, as you say, i change If it still fails, you may very well have a failed motherboard. Log in om deze video toe te voegen aan een afspeellijst. http://en.community.dell.com/support-forums/desktop/f/3514/t/19355664
If it boots up, then its a bad stick. Back to top #5 gorilakhan gorilakhan Topic Starter Members 6 posts OFFLINE Local time:05:08 AM Posted 27 September 2013 - 05:22 AM Dear Ravi, Thank you so much for Reseat the processor.
Beep Codes Your computer might emit a series of beeps during start-up if the monitor cannot display errors or problems. Back to top Page 1 of 2 1 2 Next Back to Internal Hardware 1 user(s) are reading this topic 0 members, 1 guests, 0 anonymous users Reply to quoted postsClear Disconnect all internal and external peripherals, and restart the computer. Dell Optiplex 745 Beep Codes 1-3-2 Type 2 to start the Dell Diagnostics.
Furthermore, testing my Dell earlier, I found that by tapping the F12 key, (where you might usually tap F8), before any screens/logos, appeared, the F12 Boot Menu was displayed. Dell Optiplex 745 Led Error Codes Then connect back all the peripherals and check if the system switches ON. Back to top #3 gorilakhan gorilakhan Topic Starter Members 6 posts OFFLINE Local time:05:08 AM Posted 25 September 2013 - 04:20 AM Thanks bory504. claptonman, Oct 19, 2011 #2 voyagerfan99 Master of Turning Things Off and Back On Again Staff Member Messages: 22,017 If you pull all the memory out and turn it on it
If you are getting the same error code with the new ram, try starting the computer using 1 module at a time in different slots. 0 LVL 91 Overall: Level Dell Optiplex 745 Light Codes Note : Please click on the title of the section you want to open below, in order to see the contents. Status lights 3 and 4 are still the only ones lit. Click the Change or Remove Program icon.
http://phubner.eng.ua.edu/Files/Optiplex%20745/trouble.htm 0 LVL 91 Overall: Level 91 Components 39 Desktops_PCs 27 PCs 26 Message Active today Expert Comment by:nobus2009-10-05 Here my troubleshooting procedure : with a new motherboard : verify can you please tell me what to do now.... Dell Optiplex 745 Error Codes 1 2 3 Ensure that no special memory module/memory connector placement requirements exist (see Memory).Verify that the memory modules that you are installing are compatible with your computer (see Memory).If the problem persists, contact Dell Optiplex 745 Error Codes 3 4 Hard-disk configuration error Hard-disk controller failure Hard-disk drive failure Hard-disk drive failure See Drive Problems.
NOTE: The next steps change the boot sequence for one time only. http://applecountry.net/dell-optiplex/dell-optiplex-330-error-codes-1-3.php Bezig... Parameters Allows you to customize the test by changing the test settings. If identified the card failed, replace the card. Dell Optiplex 745 Boot From Usb
Kies je taal. Close some programs and try again Close all windows and open the program that you want to use. If the computer does not boot, contact Dell for technical assistance (see Contacting Dell). http://applecountry.net/dell-optiplex/dell-optiplex-755-boot-error-codes.php If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error.
Solid green power light and no beep code but the computer locks up during POST An integrated system board device may be faulty. Dell Optiplex 745 Startup Problem Disconnect the power cable from the wall. A required.DLL file was not found The program that you are trying to open is missing an essential file.
Select the program you want to remove. Once the operating system starts to load, they turn off and are no longer visible. If customer can assist to troubleshoot, narrow down the issue by removing one by one to determine which card failed. Dell Optiplex 745 6 Beeps Taal: Nederlands Contentlocatie: Nederland Beperkte modus: Uit Geschiedenis Help Laden...
Gepubliceerd op 2 jul. 2015 Categorie Mensen & blogs Licentie Standaard YouTube-licentie Laden... The symptoms don't point to memory, try a PCI graphics card to verify that the onboard video isnt dead. can anyone please help me... http://applecountry.net/dell-optiplex/dell-optiplex-error-codes-1-3.php If you can assist to troubleshoot, narrow down the issue by removing one by one the storages on motherboard to determine which one failed.
Solid White System is in S0 state. When to Use the Dell Diagnostics If you experience a problem with your computer, perform the checks in this section and run the Dell Diagnostics before you contact Dell for technical it will show the problem ! 0 Message Author Comment by:blackm32009-10-05 hi nobus its a optiplex 745 small factor cannot change the graphics card on it. If it doesn't contact your technical support If it does add the memory modules back one at a time until the fault re-occurs, test that module in another slot and contact
S6 STO 3, 3 3 blinks followed by a short pause, 3 blinks, long pause, then repeats No Memory detected If customer can assist to troubleshoot, narrow down the issue by