Steady Amber A possible motherboard failure has occurred. Steady Green A possible floppy drive or hard drive failure has occurred. A possible system board failure has occurred. If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error. http://applecountry.net/dell-optiplex/dell-optiplex-760-error-code-1-3.php
Diagnostic Indicator Table State State Name Power Light: Amber Blinking Amber Blinking Pattern Problem Description Suggested Resolution - - 2, 1 2 blinks followed by a short pause, 1 blink, long Log in om je mening te geven. Right-click Local Disk C:. S8 MEM 3, 5 3 blinks followed by a short pause, 5 blinks, long pause, then repeats Memory configuration or incompatible error Memory subsystem configuration activity is in progress. my response
Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available. A program stops responding End the program Press
I know we've had several problems prior to just the power supplies.. These LEDs do not indicate the problem that caused the POST routine to stop. Reseat any installed graphics cards. Dell Optiplex 990 Error Code 1 3 4 For additional safety best practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance.
Power Button LEDs Power Button LED State Description Off Power is Off. Dell Optiplex 760 Diagnostic Lights 1 3 4 If identified the memory failed, replace the memory. Plug the computer into a working electrical outlet and press the power button.If the problem persists, contact Dell (see Contacting Dell). Possible peripheral card or system board failure has occurred.
Symptom Tree This option allows you to select tests based on a symptom of the problem you are having. Dell Optiplex 760 Diagnostic Lights 2 And 3 If you receive an insufficient memory message Save and close any open files and exit any open programs you are not using to see if that resolves the problem.See Ensure that the voltage selection switch is set to match the AC power at your location (if applicable).Ensure that all components and cables are properly installed and securely connected to the Laden...
All Replies Posted by RoHe on 27 Nov 2013 11:45 Manual(page 162) doesn't say anything about the LEDs flashing, but a blinking amber power button with LEDs 1&3: A possible motherboard, Posted by RoHe on 29 Jan 2014 12:46 I pinged my Dell tech contacts and they're going to look into this problem. Dell Optiplex 760 Error Lights 3 4 Turn off nearby devices to check for interference. Dell Optiplex 760 1 And 3 Flashing If the problem persists, the system board / system board component is probably bad.
If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error. his comment is here Windows Vista: Click Start ® Control Panel® Hardware and Sound® Printer. If only one memory module is installed, try moving it to a different DIMM connector and restart the computer. The device is not ready The drive cannot read the disk. Dell Optiplex 760 1 And 3 Flashing Green
If the computer boots, add the peripheral cards back one by one until you find the bad one. When the computer starts normally, the lights flash, and then turn off. Thank you. this contact form If this answers your question, please click Yes Ron Forum Member since 2004 I amNOT a Dell employee Like 0 Reply You have posted to a forum that requires a
Right-click Local Disk C:. Dell Optiplex 980 Error Code 1 3 ABCD MEM Memory subsystem configuration activity or failure Remove all memory from PC, does the LED code change? If the computer boots, add the peripheral cards back one by one until you find the bad one.
Sometimes this work and others I have to unplug everything from the motherboard, wait a couple of minutes and plug it in again. Tech Steve 29.573 weergaven 20:10 How to fix Dell Optiplex 745 Battery Voltage low Press F1 - Duur: 4:02. Starting the Dell Diagnostics From Your Hard Drive Before running the Dell Diagnostics, enter System Setup (see the Entering System Setup) to review your computer's configuration information, and ensure that the Optiplex 780 Diagnostic Lights Remove the Drivers and Utilities media from the optical drive.
The computer hardware is operating normally but the BIOS may be corrupt or missing. Contact Dell (see Contacting Dell). This is the normal power states of a functioning machine. navigate here Steady Green A possible expansion card failure has occurred.
These indicators are merely a starting point to narrow down any troubleshooting you will carry out to identify the cause of your current issue. Bypass power strips, power extension cables, and other power protection devices to verify that the computer turns on properly. Je kunt deze voorkeur hieronder wijzigen. Autoplay Wanneer autoplay is ingeschakeld, wordt een aanbevolen video automatisch als volgende afgespeeld.
Disconnect all internal and external peripherals, and restart the computer. If you purchased a sound card, ensure that the speakers are connected to the card. Type hardware troubleshooter in the search field and press
If customer can assist to troubleshoot, narrow down the issue by removing one by one the memory on motherboard to determine which one failed. CMOS checksum error Possible system board failure or RTC battery low. Check the mouse cable Ensure that the cable is not damaged or frayed and check cable connectors for bent or broken pins. Sluiten Meer informatie View this message in English Je gebruikt YouTube in het Nederlands.
Keyboard Problems WARNING: Before working inside your computer, read the safety information that shipped with your computer.