To remove and then reinstall the program: Click the Start button and click Control Panel. Seuss, Oh, the Places You'll Go! 0 Sign In or Register to comment. motherboard bios post dell-optiplex share|improve this question edited Apr 17 at 7:01 magicandre1981 54.6k1377114 asked Nov 17 '14 at 1:53 kelario 195 add a comment| 1 Answer 1 active oldest votes I guess they are all a toast or recylcing material. http://applecountry.net/dell-optiplex/dell-optiplex-gx270-led-error-codes.php
See "Floppy drive problems" or "Hard drive problems" for troubleshooting suggestions. It was made during Windows 2000 so its very old. A B C - If A B and C are yellow, this means the BIOS is not running or not finishing (completing its POST). Does anyone still have this document, or a reference for the error codes the 4 lights on the back of the tower generate? http://en.community.dell.com/support-forums/desktop/f/3514/t/17756021
Then, shut down the computer, reinstall the hard drive, and restart the computer. DISK C: FAILED INITIALIZATION The hard drive failed initialization. How do R and Python complement each other in data science? Solid green and a beep code during POSTA problem was detected while the BIOS was executing.See "Beep Codes" for instructions on diagnosing the beep code.
You may accidentally misalign the heads, which can render the drive inoperable. No timer tick interrupt A chip on the system board might be malfunctioning. The general consensus is motherboard failure. Dell Optiplex Gx270 Motherboard Join Now Optiplex GX270 models.
One possible beep code (code 1-3-1) consists of one beep, a burst of three beeps, and then one beep. Dell Optiplex Gx270 Troubleshooting When your computer finishes booting, immediately back up your data and replace your hard drive. Ensure that the device is turned on Firmly press the device's power button. Clicking Here Could not find this light pattern in my cheat sheet.
The manual should tell you all of the various codes. Dell Optiplex Gx270 Open Case Remove and then reinstall the memory modules. Click your connection type to highlight it. Press the power button again to restart the computer.
This series of beeps, called a beep code, identifies a problem. http://www.pctechbytes.com/dell/dell-diagnostic-lights/ SECTOR NOT FOUND The operating system cannot locate a sector on the hard drive. Dell Optiplex Gx270 Diagnostic Lights BIOS Chip System board failure, covers BIOS corruption or ROM error 2 No RAM Detected No memory detected 3 Chipset Error (North and South Bridge Chipset, DMA/IMR/Timer Error for Intel platform); Dell Optiplex Gx270 Drivers Rarely, do the CPU's die before the mobos do. 0 Tabasco OP nichomach Apr 30, 2013 at 2:02 UTC Indeed - wonky caps agogo; if your motherboard looks
Enter system setup and ensure that the boot sequence information is correct. this contact form If the problem persists, reinstall the card that you removed, remove a different card, and then restart the computer. Try different settings for Screen area or Desktop area. Gate A20 failure Super I/O chip failure Keyboard controller test failure. 4 RAM Read/Write failure Memory failure 5 RTC Power Fail COMS battery failure 6 Video BIOS Test Failure Video card Dell Optiplex Gx270 Specs
Reinstall the memory modules and, if necessary, replace them. If the hard drive is your boot device, ensure that the drive is installed, properly seated, and partitioned as a boot device. Click View installed printers or fax printers. http://applecountry.net/dell-optiplex/dell-optiplex-gx270-fan-error.php There are many reasons for wanting to remove this icon.
The delay between each beep is 300ms. Dell Optiplex Gx270 Memory I've replaced the motherboard because I think it was the problem part, and the hard drive because it failed later. Reinstall the memory modules and, if necessary, replace them.
The device is not ready The floppy drive cannot read the disk. We will list a few of the most common here, but there are certainly more on the Dell website. All rights reserved. Dell Optiplex Gx270 Review the value of your time and cost of new caps0 Pimiento OP Nic8721 Apr 30, 2013 at 2:14 UTC 1st Post I get this quite frequently on
Registered User regular July 2008 edited July 2008 Optiplex GX270 showing a D LED? Not a boot diskette The operating system is trying to boot to a floppy disk that does not have a bootable operating system installed on it. Other technical problems Go to the Dell Support website Go to support.dell.com for help with general usage, installation, and troubleshooting questions. Check This Out Go and look at them!
A sound card emits noise or demonstrates other problems. When I plug the power cable, the fans start spinning, HDD seems to be spinning too but hard to tell for sure. Invalid configuration information – please run SETUP program The computer configuration information does not match the hardware configuration. Insert a bootable floppy disk or CD.
DECREASING AVAILABLE MEMORY One or more memory modules may be faulty or improperly seated. If, however, you have anything different, you can look up your model on the Dell website for further documentation on these error codes.