Memory address line failure at address, read value expecting value A memory module may be faulty or improperly seated. System board Failure (Power LED Blinking Amber) Run the Dell Diagnostics 4 RAM Read/Write failure Memory failure Troubleshoot the Memory 5 RTC Power Fail COMS battery failure Run the Dell Diagnostics No memory modules were detected. 1- Solid2- Off3- Off4- Solid Fatal system board failure detected. 1- Solid2- Off3- Solid4- Off Memory subsystem configuration activity is in progress. Troubleshoot the Memory 5 Real Time Clock (RTC) power fail Run the Dell Diagnostics 6 Real Time Clock failure Run the Dell Diagnostics 7 Video card or chip failure. Source
Replace the CPU with a known good CPU. Diagnostic LEDs for the OptiPlex series (2005 to 2009) This series had a combination of Power button LED states and the A, B, C, B, block was replaced with 1, 2, Diagnostic Beep Codes Code Cause 1-1-2 Microprocessor register failure 1-1-3 NVRAM 1-1-4 ROM BIOS checksum failure 1-2-1 Programmable interval timer 1-2-2 DMA initialization failure 1-2-3 DMA page register read/write failure 1-3-1 BIOS Chip System board failure, covers BIOS corruption or ROM error Run the Dell Diagnostics 2 No RAM Detected No memory detected Troubleshoot the Memory 3 Chipset Error (North and South http://www.dell.com/support/article/us/en/04/SLN284978/en
Reinstall the memory modules and, if necessary, replace them. NO BOOT SECTOR ON HARD DRIVE The operating system may be corrupted. Shut down the computer, remove the hard drive, and boot the computer from a CD.
Note : If you have an OptiPlex AIO (All In One) System. If it doesn't contact your technical support If it does add the memory modules back one at a time until the fault re-occurs, test that module in another slot and contact A possible system board failure has occurred. Dell Optiplex Gx520 Error Codes If available, install a working graphics card into your computer.If the problem persists, contact Dell .
Starting from the D4 generation of OptiPlex models onwards (7010/9010/9010 AIO), the beep codes will be eliminated, replaced by a single memory error pattern Now only "no memory failure" conditions generate Dell Optiplex Gx270 Error Codes Run the Windows error-checking utility to check the file structure on the hard drive. With a few clicks of the mouse, a service technician can paste the complete error code into his or her tracking software. http://www.dell.com/support/article/us/en/19/SLN293445 You may have a defective sector or corrupted FAT on the hard drive.
Memory allocation error The software you are attempting to run is conflicting with the operating system, another program, or a utility. Dell Optiplex Error Codes 1 3 Adamant IT 28.246 weergaven 10:03 Mi pc Parpadea color Naranja DELL Optiplex (SOLUCIONADO) - Duur: 4:22. This is actually a BIOS controlled state and is also S0e. 1- Off2- Off3- Off4- Off Windows Standby State. 1- Off2- Off3- Off4- Off Hibernate or Soft off. The new beep codes emit only memory failure symptoms.
TIMER CHIP COUNTER 2 FAILED A chip on the system board may be malfunctioning. Enter system setup (see Entering System Setup), review your computer's configuration information, and ensure that the device you want to test displays in System Setup and is active. Dell Optiplex 755 Error Codes Contact Dell and report the checkpoint code (nnnn) to the support technician. Dell Optiplex Gx280 Error Codes Diagnostic LEDs for the OptiPlex series (Prior to 2005) This series of systems had a block of A, B, C, D LEDs on the back of the chassis that lit up
Reinstall the memory modules and, if necessary, replace them. this contact form Select Run the 32 Bit Dell Diagnostics from the numbered list. If the computer boots, add the peripheral cards back one by one until you find the bad one. Link to Fix PSA 1000-0144PSA+ 2000-0144 No support for Drive Self Test. Dell Optiplex Gx620 Error Codes
Diskette subsystem reset failed The floppy drive controller may be faulty. S6 STO 3, 3 3 blinks followed by a short pause, 3 blinks, long pause, then repeats No Memory detected If customer can assist to troubleshoot, narrow down the issue by Contact your technical support to take this further. 34 MEM Memory subsystem configuration activity or failure Remove all memory from PC, does the LED code change? have a peek here A possible USB failure has occurred.
Light Pattern Problem Description Suggested Resolution The computer is in a normal off condition or a possible pre-BIOS failure has occurred. Dell Optiplex 755 Error Codes 2 And 4 No POST, No Power, No Video on a Dell Desktop Computer. If you can assist to troubleshoot, narrow down the issue with reseating memory and swapping a known good memory if available.
If a beep code is emitted, write it down on a copy of the Diagnostics Checklist and look it up in the following table. If nothing works, replace the memory. Memory modules are detected, but a memory failure has occurred. Dell Optiplex 960 Error Codes 1 And 3 Instead the Power Button state now gives a blink and colour shift pattern to indicate where its had a problem.
GENERAL FAILURE The operating system is unable to carry out the command. BIOS Chip System board failure, covers BIOS corruption or ROM error 2 No RAM Detected No memory detected 3 Chipset Error (North and South Bridge Chipset, DMA/IMR/Timer Error for Intel platform); Figure 1: Dell Diagnostic Reference Chart. Artikel-id: SLN144981 Laatste wijzigingsdatum: 05/30/2012 12:00 AM Beoordeel dit artikel Nauwkeurig Nuttig Eenvoudig te begrijpen Was dit artikel nuttig? http://applecountry.net/dell-optiplex/dell-optiplex-520-error-codes.php Probeert u het later nog eens.
S4 PCI 3, 1 3 blinks followed by a short pause, 1 blink, long pause, then repeats PCI Device or Video subsystem failures PCI device configuration activity is in progress or Reinstall the memory modules and, if necessary, replace them. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support. This video goes through the replacement and troubleshooting steps to make sure that it's not the slot and that you have the correct memory module.
This is the transition state to POST states. 1- Solid2- Off3- Off4- Off - Reserved 1- Blink2- Off3- Off4- Blink A power failure has been detected on a plug-in component such Close all windows and open the program that you want to use.