See "Getting Help." No boot sector on hard-disk No operating system on hard drive.Check the hard-drive configuration settings in the System Setup program. Move DIMM3_A and DIMM3_B into DIMM2_A and DIMM2_B. Drive onlineThe green power-on/fault indicator is on.Back-Panel Features and Indicators Figure1-4 shows the controls, indicators, and connectors located on the system's back panel. I read the user manual and it says: The amber system status indicator flashes when the system needs attention due to a problem with power supplies, fans, system temperature, or hard have a peek here
See FigureA-2 for jumper location. SCSI device drivers that allow the operating system to communicate with devices attached to the integrated SCSI subsystem. I'm pretty sure it's a hardware problem. Memory modules are not installed in consecutive banks.
If the problem persists, replace the system board. Keyboard controller failure Faulty keyboard controller (faulty system board). Supported Operating Systems Your system supports the following operating systems:Microsoft Windows NT® 4.0 Server Microsoft Windows 2000 Server and Advanced Server Red Hat Linux 7.x Novell® NetWare® 5.1 and NetWare 6.0
AC line status Green indicates that a valid AC source is connected to the power supply.NIC Indicator Codes Figure2-6 and Table2-6 describe the indicators on the NIC. Ensure that all memory modules are properly installed. Must power down. OffBlinkingThe system has detected an error.
See "Getting Help." 1-2-21-2-3DMA initialization failureDMA page register write/read failureRemove and reseat the memory modules. Dell Poweredge 1650 Manual If the problem persists, replace the memory modules. Swap memory modules in slots DIMM2_A and DIMM2_B with modules in DIMM1_A and DIMM1_B. The SCSI backplane automatically configures SCSI ID numbers and SCSI termination on individual hard drives, greatly simplifying drive installation.
See "Installing Expansion Cards" in "Installing System Board Options." If the problem persists, replace the expansion card(s). And how can I find out the temperature? Documentation is included with any options you purchased separately from the system and provides information you need to configure and install these options in your system. If the problem persists, see "Getting Help." Memory parity failure at start address to end address Memory parity error at address Improperly seated or faulty memory modules.Remove and reseat the memory
See "Getting Help." 1-2-1Programmable interval-timer failureReplace the system board. https://cs.uwaterloo.ca/~brecht/servers/docs/PowerEdge-2600/en/Pe1650/UG/8g540c10.htm See "Replacing the Processor" in "Installing System Components." Check for a BIOS update using the Dell Support website at support.dell.com. Dell Poweredge 1650 Power Consumption Figure 2-4. SCSI Hard-Drive Indicators Table2-3 lists the drive indicator patterns. Dell Poweredge 1650 Specs Ensure that only single rank memory modules are installed in slots DIM3_A and DIMM3_B.
hard-drive indicator The green hard-drive activity indicator flashes when the hard drives are in use (see Figure2-4 for more information on hard-drive indicators). http://applecountry.net/dell-poweredge/dell-poweredge-error-messages.php If the controller is removable, take the controller out and then see if the computer will continue past the bios. Power supply fault Amber indicates a problem with the power supply. video connector Connects a monitor to the system.Back-Panel Features and Indicators Figure2-2 shows the controls, indicators, and connectors located on the system's back panel.
Diagnostics Messages When you run a test group or subtest in the system diagnostics, an error message may result. The front panel also incorporates a USB connector, a video connector, and a PS/2 connector to connect a mouse and keyboard using a Y-cable (see Figure1-2). Let me know what you find and I will get you the updates if needed. Check This Out See "Getting Help." System backplane error Improperly attached or missing SCSI backplane.Check that the SCSI backplane board is fully seated.
Check the Integrated Devices configuration settings in the System Setup program. For more information on these help tools, see "Getting Help" in your Installation and Troubleshooting Guide. See "Opening the System Doors" in "Checking Inside the System" for information on accessing the inside of the system.
If problem persists, replace the system board. See Figure2-3. Ensure that the diskette drive and optical drive cables are properly connected. Line conditioners keep a system's AC power source voltage at a fairly constant level and provide protection from brownouts of short duration.
Table 2-4. Power Button Indicators Indicator Function On Indicates that power is supplied to the system and the system is operational. See "Finding Software Solutions" and the documentation that accompanied the operating system or application program for more information on warning messages. See"Disabling a Forgotten Password" in "Jumpers and Connectors." System parity error Defective expansion card(s) or improperly seated or faulty memory modules (reported by the NMI handler).Replace expansion cards one at a http://applecountry.net/dell-poweredge/dell-poweredge-error-e0cf1.php You will also see the drive-activity indicator blink when the drive is being accessed.
See "Getting Help." 1-1-4 BIOS error Reflash the BIOS. 1-2-1 Programmable interval-timer failure; faulty system board Faulty system board. Ensure that the RAC is properly installed. I maintain the server via Webmin and there isn't any information about an error there either. See "Getting Help." Processor bus error PCI bus error IMB bus error Defective system board (reported by the NMI handler).Replace the system board.
If the problem persists, see "Getting Help." Processor 1 internal error Processor 2 internal error Defective microprocessor or system board (reported by the NMI handler).Replace the specified microprocessor. If dual-rank memory modules are installed in the system, they must be installed in slots DIMM1_A and DIMM1_B. And how can I find out the temperature? Green Off Indicates that the network adapter is connected to a valid link partner on the network, but data is not currently being sent or received.
Ensure that either SCSI Controller, Diskette Controller, or IDE CD-ROM Controller is enabled. NOTE: If the optional ROMB card is not installed, you will see only the "drive online" indicator pattern. This may or may not be a 730X. \015\012\015\012Yes I had the same PSA test error. Drive online The green power-on/fault indicator is on.Power Indicator Codes The power button on the front panel controls the power input to the system's power supplies.
Power supply fault Red indicates a problem with the power supply Power supply statusGreen indicates that the power supply is operational. on 25 Oct 2004 19:58 This isa link to the DSET utility, copy the link into your browser. Since I assumed you were running Windows, HERE is the link for the Linux documentation for OpenManage share|improve this answer edited May 18 '12 at 12:03 answered May 17 '12 at If the problem still persists, replace the system board. 1-3-3 1-3-4 1-4-1 1-4-2 2-1-1 through 2-4-4 Chip set or data line failure in the first 64
If the problem still persists, replace the system board. 4-3-3 Defective system board Replace the system board. 4-3-4 Time-of-day clock stopped Replace the battery. See "Using the System Setup Program" in the User's Guide. See "Installing Drives." If the problem persists, replace the system board.