Covered by US Patent. Printer says error 1203 what do I do ??... Adv Reply July 23rd, 2009 #2 apel_2804 View Profile View Forum Posts Private Message Visit Homepage A Carafe of Ubuntu Join Date Jun 2007 Location Germany Beans 88 Re: PowerVault Kapono_Hohaia Level 2 03-20-2006 02:02 PM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content Ben,I finally got mine to work http://applecountry.net/dell-powervault/dell-powervault-124t-drive-error-type-3d.php
Step 4 led me to the SCSI LUN configuation, which indicated that I needed to enable BIOS MULITPLE LUN SUPPORT. In the SCSI BIOS of the card the loader is attached to, make sure Multi-LUN support is enabled. Veritas drivers get installed for the Drive, but not for the autoloader. We looked at online and RAID based backups, online was too expensive.
Resultaten weergeven Terug naar productsupport Productsupport × Verouderde browser gedetecteerd. Het is ons opgevallen dat u een oudere versie van Internet Explorer gebruikt. Dell suggested upgrading the firmware to V31 (it was on V27). Sharvari_Deshmu Level 6 02-16-2006 09:13 AM Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content Hello,Please follow the steps below:1. Dell Powervault 124t Tape Stuck In Drive It's most likely the SCSI card settings.
Note: The Random Moves test requires a minimum of two cartridges present within the autoloader. Dell Powervault 124t Manual Really appreciate it. Turn the white thumbwheels on each magazine and insure that the carriers move freely at least one full rotation in each direction. https://www.experts-exchange.com/questions/28208793/Symantec-Backup-Exec-2010-R3-can-no-longer-see-Dell-PowerVault-124T-tape-drive.html I use commodity RAID boxes for storage and point backups to it.
To set a dynamic IP address: 1.From the main menu, scroll to Configuration , and then press Enter . 2.From the Configuration menu, scroll to Ethernet , and then press Enter Dell Powervault 124t Drivers Voor de beste ervaring gebruikt u Chrome of FireFox, of werkt u Internet Explorerbij. Win2003 Device Manager showed the autoloader under Medium Changers and the Certance Ultrium2 tape drive under Tape Drives.After starting BackupExec V10 rev 5484, the Certance tape drive was switched to a l Check support.dell.com for PowerVault 124T firmware updates.
Good luck. 0 Kudos Reply Re: Veritas Driver for Dell PowerVault 124T? https://ubuntuforums.org/showthread.php?t=1221147 So I tried to remove an empty tape (never used before) from slot 6 and then inserted tape #AA to retrieve the data. Dell Powervault 124t Error Codes It installs a Veritas driver for the Tape Drive, but not for the autoloader. 0 Kudos Reply Re: Veritas Driver for Dell PowerVault 124T? Dell Powervault 124t Password DLTtape is a registered trademark of Quantum Corporation. Adobe is either a registered trademark or trademark of Adobe Systems Incorporated in the United States and/or other countries.
error 1203. Dell Powervault 124t Drive Taflag 39 l Time server IP address (or the time zone, date, and time, if configuring manually) — only if a time server is being used. The Wizard "sees" the tape drive fine and changes the drivers from Dell to Veritas.
l Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control Panel (OCP). The default password for the Operator is 111111 . To configure the Dell PowerVault 124T LTO5-140 SAS autoloader, you must verify the setup of the following: l Magazine(s). Specifically, how did you set up amanda.conf to use it. Dell Powervault 124t Drive Requests Cleaning Third party tools should also be used.
Edit: A long story short. However, after you set the security option, all the configuration functionality is password-protected. Join our community for more solutions or to ask questions. this contact form It is probably something simple to re associate the tape drive and backup exec, but I have not been able to find it.
I am not sure what happened, we have had some power fluctuations and UPS trouble, but as it stands right now when I go to start a backup job, it immediately It's when we're reading data from the tape. So debating the pros/cons of the backup scheme won't help me at this point. Where can I check on that error message?Something else...the Dell PV124T is not listed in the SCSIChanger key in the Server Registry.Is that an issue?Thanks in advance... 0 Kudos Reply Re:
l If all previous steps fail, contact support.dell.com. 27 Message Type Bad 28 Message Parameter Bad Stack/Global Data Corruption Error Types 29 Invalid Element l Verify the host backup application and The LCD front panel default password for the Administrator is 000000 . To use the Ethernet connection, you must define the following: l A dynamic or static IP address for the autoloader (required) l A subnet mask (required for static IP), not required If you cannot resolve the problem yourself, contact your service representative or go to the Dell Support website at support.dell.com .
We already have quotes to renew our licenses. Join Date Jan 2005 Location Copenhagen, Denmark Beans 173 DistroUbuntu Karmic Koala (testing) Re: PowerVault 124T Tape Read Errors We have begun to get the same kind of errors, with NovaNET I haven't been able to verify the card's firmware settings because I've been working on the system remotely, but once I'm back in the office, I'll verify whether multiple LUN support