Check your password, and then try again. Search for "telephon.ini". - If you find this file, rename it to "telephon.old". - Go back to the Start Menu and open Run (you may need to search for "run"). Type in tapiini.exe and press the Enter key on your keyboard. Dialup error 741: The local computer does not support encryption. check over here
Dialup error 708: The account has expired. Check your server type settings in the properties of the connection. If you live in a rural area, a weak telephone line signal could be the cause. Try this: - Make sure you're dialling the correct dialup number. http://editor.actrix.co.nz/byarticle/dune650.htm
Dialup error 666: Your modem (or other connecting device) is not functioning. If the modem is external; turn the modem off and then back on. Dialup error 645: Internal authentication error. When Dialing up, being dropped off current network when connected to new one.
Dialup error 737: Loopback detected. Search for the telephon.ini file (usually located in C:\Windows). Dialup error 601: The port handle is invalid. Error 680 - Your pet has been playing with that phone line!
The last one of these could deal with your account and its status. You may need to consult with your hardware's manufacturer to be sure you modem will work with Windows 7. Restart the computer and try the connection. http://www.iinet.com/support/answer.php?id=64 Try this: - Check to see if your Home Phone has line noise.
Reconfigure the LAN connection with a single IP address before enabling Internet connection sharing. Remove any VPN adapters (dial-up only), NetBEUI dial-up protocols and IPX/SPX Compatible Protocols for the Dial-up adapter. Article ID: Q188189 Error172: (no server assigned) the request is not seen on the network. Most times that will be a 9.
Dialup error 623: Cannot find the phone book entry. Try this: - Please ensure you're dialling the correct dialup number. Dialup error 658: The device name in the device .INF or media .INI file is too long. Try this: - Open the Start Menu and then open the Control Panel. - Select Network and Internet Connections and then click Network Connections. - Right-click your Dialup connection and select
Pick up the phone and listen for a dial tone. http://applecountry.net/dial-up/dial-up-networking-error-732.php Dialup error 665: The port is not configured for remote access. Dialup error 5: Access denied/Invalid procedure call. But since not many of us have NT, these are rare.
See MS KB Q162847 Error 650 can also occur if the ISP server modem/equipment is not set up properly. Dialup error 783: Internet Connection Sharing cannot be enabled. If you see "RNAAPP" running, select it and then click End task. this content Dialup error 605: Cannot set port information.
Dialup Errors Dialup error 2: The system cannot find the file specified. Go to properties, of the Dial-Up connection, server tab and press the TCP-IP settings button. Windows NT 4.0: Under the Server tab, make sure the only thing check-marked under Allowed Network Protocols is TCP/IP.
If this doesn't work, contact your computer's or modem's manufacturer. Please try another. Dialup error 633: The port is already in use or is not configured for remote access dial-out. Dialup error 603: Caller's buffer is too small.
If you have disabled Call Waiting when you connect to the Internet, make sure you are dialing the correct prefix. Dialup error 704: ERROR BAD CALLBACK NUMBER. Dialup error 694: ERROR DCB NOT FOUND. have a peek at these guys Dialup error 685: ERROR WRITING MAXCONNECTBPS.
Try calling the number on a regular telephone and listen for modem tones. One comma in the dialling sequence will make the modem pause for one second. - For example, if you have to dial 0 and then wait 2 seconds before dialling the Dialup error 674: Cannot read the maximum connection BPS rate from the media .INI file. If this problem is occuring on a laptop computer, try plugging the PCMCIA card into a different slot.
Try this: - When connecting to dialup, click Properties. Dialup error 632: The structure size is incorrect. Dialup error 705: ERROR INVALID AUTH STATE. Article ID: Q190554 Error630: The computer is not receiving a response from the modem.
Try to lower the port speed to 57600 in the modem properties and disable v90, you can do this by adding an extra setting ie. Try this: - Please ensure you're dialling the correct dialup number. Dialup error 380: Invalid property value. Error 678: The computer you are dialing is not answering.
Try this: - Hold down the CTRL, ALT + DELETE keys on your keyboard and open the Task Manager. Dial-Up Networking has become corrupt, Reinstall Dial-Up Networking. You want the wire from the wall jack plugged in to the modem telephone jack that says "Line" or "Line In." Plug a normal phone into the wall jack that your Dialup error 746: An essential file failed to initialise.
Possible Resolution: Reinstall your modem using the correct drivers provided by the manufacturer for Windows 7. Dialup error 679: Cannot detect carrier. Here are some common ways in which one may resolve this problem. Dialup error 758: Internet connection sharing is already enabled on the connection.