Diagnostic LEDs for the OptiPlex series (2005 to 2009) This series had a combination of Power button LED states and the A, B, C, B, block was replaced with 1, 2, A possible USB failure has occurred. A possible floppy drive or hard drive failure has occurred. Plug the computer into a working electrical outlet and press the power button. Source
If the problem persists, contact Dell (see Contacting Dell).
A possible CPU or system board failure has occurred. By continuing to browse our site you agree to our use of data and cookies.Tell me more | Cookie Preferences Partially Powered By Products Found At Lampwrights.com Fandom Skip If nothing works, replace the memory. This is actually a BIOS controlled state and is also S0e.
If a problem is encountered during a test, a message appears with an error code and a description of the problem. Ensure that the memory you are using is supported by your computer. Sign in here. Dell Optiplex 960 Error Code 123 Any help would be greatley needed Dennis Remove Advertisements Sponsored Links TechSupportForum.com Advertisement 07-27-2010, 05:26 PM #2 Ben Her Registered User Join Date: Jul 2010 Posts: 330
Ensure that no special requirements for memory module/connector placement exist. Dell Error Code 0123 thanks anyway :) Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available. Blinking Amber — System fault error condition including Power Supply (only +5VSB working), Vreg failure, missing or bad CPU. Recent Topics 1 Need Help and Suggestions With Headsets By Anthony SugihartoStarted 4 minutes ago Posted in General Discussion 6 Accidentally Rounded Out A Screw On Video Card By Godlygamer23Started 6
If none of the card failed, replace the motherboard. Dell Optiplex 760 Error Code 123 Repeat this process for each expansion card installed. Replace the CPU with a known good CPU. Four (4) single color LEDs are incorporated on the front control panel to serve as a diagnostic aid for troubleshooting systems exhibiting No Post/ No Video symptoms.
Ensure that all hard drive and optical drive cables are properly connected to the system board. http://www.tomshardware.com/forum/350860-28-optiplex-boot-beeps-lights Sign In Sign In Remember me Not recommended on shared computers Sign in anonymously Sign In Forgot your password? Dell Error Code 123 Optiplex 755 Contact your technical support to take this further. 34 MEM Memory subsystem configuration activity or failure Remove all memory from PC, does the LED code change? Dell Error Code 1 2 3 No memory modules are detected.
Back to Contents Page Jump to content arrow_back menu All Content All Content This Topic This Forum Advanced Search search Existing user? http://applecountry.net/error-code/dell-the-error-code-is-110.php Memory modules are detected, but a memory failure has occurred. If available, install working memory of the same type into your computer. Generally this means the motherboard is gone. Dell Optiplex 980 Error Code 123
Select Run the 32 Bit Dell Diagnostics from the numbered list. If identified the card failed, replace the card. Games Movies TV http://applecountry.net/error-code/dell-error-code-150.php NOTE: The next steps change the boot sequence for one time only.
Contact Us Back to Top Artikel-id: SLN284978 Laatste wijzigingsdatum: 09/16/2016 09:27 AM Beoordeel dit artikel Nauwkeurig Nuttig Eenvoudig te begrijpen Was dit artikel nuttig? Dell Error Lights 123 If identified the memory failed, replace the memory. When the tests are completed, if you are running the Dell Diagnostics from the Drivers and Utilities disc, remove the disc.
Most beep codes indicate a fatal error that prevents the computer from completing the boot routine until the indicated condition is corrected. Also, combining the configuration to validate appropriate combination. If two or more memory modules are installed, remove the modules, then reinstall one module and restart the computer. Dell Error Beep Codes A possible system board failure has occurred.
You could identify these models by their flat black front face and grey side panels/lids. Reseat the power cable in the power connector on the back of the computer and the electrical outlet. If two or more memory modules are installed, remove the modules (see your service manual), then reinstall one module (see your service manual and restart the computer. Check This Out Beep Codes If the monitor cannot display error messages during the POST, the computer may emit a series of beeps that identifies the problem or that can help you identify a
Ja Nee Stuur ons feedback Feedback bevat ongeldig teken, speciale tekens die niet worden geaccepteerd zijn <> () \ Feedback verzenden Excuses, ons feedbacksysteem is momenteel offline. Starting the Dell Diagnostics From Your Hard Drive Turn on (or restart) your computer. Run the BIOS Recovery utility, wait for recovery completion, and then restart the computer. S6 STO 3, 3 3 blinks followed by a short pause, 3 blinks, long pause, then repeats No Memory detected If customer can assist to troubleshoot, narrow down the issue by
Reinstall the processor and restart the computer. S1 1- Off 2- Off 3- Off 4- Solid RCM System is in Recovery Mode BIOS checksum failure was detected and the system is now in recovery mode. When the DELL logo appears, press
Thanks,~Elias Main PC: Core i5 4670 | MSI Mpower Max z87 | G.Skill Ripjaws 2x4gb | Stock intel cooler | PNY GTX 770 2gb (hoping to upgrade) | Seagate 1tb 7200rpm LKD_0x141_Tdr:6_IMAG... A possible graphics card failure has occurred. Diagnostic LEDs for the OptiPlex series (2012 to Present) With the latest series, the diagnostics indicator LEDs have been removed.
Determine if a conflict exists by removing an expansion card (not a graphics card) and restarting the computer. If the problem persists, the system board / system board component is probably bad. If available, install properly working memory of the same type into your computer. Posted by Zynclair on 27 Mar 2012 1:22 thanks for the suggestion, I've fixed the problem myself just now, I just cleaned all the dust and reseat my hard disc and
Abused patience turns to fury. share Link to post Share on other sites nanowatt nanowatt Member 1,709 posts Your average public offender Posted October 28, 2014 If that doesn't work Dell Diagnostics Main Menu After the Dell Diagnostics loads and the Main Menu screen appears, click the button for the option you want. Register a new account Sign in Already have an account? S5 VID 3, 2 3 blinks followed by a short pause, 2 blinks, long pause, then repeats Video Subsystem failure Video subsystem configuration activity in progress or video subsystem failure.
Or sign in with one of these services Sign in with Facebook Sign in with Twitter Sign in with Microsoft Sign in with Google Sign in with Steam Sign Up Community Pb2 1- Off 2- Off 3- Solid 4- Off - Reserved Reserved Pb3 1- Off 2- Off 3- Solid 4- Solid ACPI S3 Suspend to RAM Windows Standby State.