Connect with me on: Google+ 25 Comments abdessamad bado November 30, 2009 dear sir my problem ihave a pc dell but does not work there is a light yellow in it Note : Please click on the title of the section you want to open below, in order to see the contents. If the hard drive activity light does not blink during the boot routine, contact Dell. See "Drive Problems" for troubleshooting suggestions. have a peek at this web-site
Memory parity errors occur on parity-enabled computers. If the problem persists, contact the hardware manufacturer for technical assistance. Click Mouse. Other software problems Consult the software documentation or contact the software manufacturer for troubleshooting information Back up your files immediately If your computer has a CD drive or a zip drive http://www.dell.com/support/article/us/en/04/SLN284978/en
A possible system board failure has occurred. If none of the storage failed, replace the motherboard. Ensure that the microprocessor power cable is securely connected to the system board.
If problem persists, replace the motherboard S2 CPU 2, 6 2 blinks followed by a short pause, 6 blinks, long pause, then repeats Bad Processor CPU configuration activity is in progress Blinking White System is in a low power state, either S1 or S3. Back to Top 1. Dell Error Beep Codes Sector not found The operating system cannot locate a sector on the floppy or hard drive.Run the Windows error-checking utility to check the file structure on the floppy disk or hard
Decreasing available memory One or more memory modules may be faulty or improperly seated.Reinstall the memory modules and, if necessary, replace them (see "Memory" for module installation procedures). Dell Dimension 4600 Abcd Error Codes These manuals are priceless in an emergency. The front switch was required to be pressed several times in order to boot the computer. http://www.pctechbytes.com/dell/dell-diagnostic-lights/ Reinstall the mouse driver See "Reinstalling Drivers." Run the Dell Diagnostics Reboot the computer and run the Dell Diagnostics.
And YOU are the one who'll decide where to go...” ― Dr. Dell Error Codes 1 3 If necessary, install additional memory (see "Memory" for module installation procedures). No boot device available The computer cannot find the floppy disk or hard drive.If the floppy drive is your boot device, ensure that a bootable floppy disk is in the drive. So any adivce would be greatly appreciated.
Blutraserei on July 2008 0 Horus Los AngelesRegistered User regular July 2008 edited July 2008 Ok found the model which did not have the documentation of the lighting but found a https://www.manualslib.com/manual/36389/Dell-Poweredge-840.html?page=15 Ensure that no special requirements for memory module/connector placement exist. Dell Error Code 0142 Blutraserei on July 2008 0 Horus Los AngelesRegistered User regular July 2008 edited July 2008 The computer does not start at all, so I cannot enter bios system so that defeats Dell Dimension 2400 Abcd Error Codes Type: Power Supply U More on DELL Power Supply Switching UNIT PS Price: $16.99 « [SOLVED] CPU and motherboards | [SOLVED] Asus Motherboard and 1394 connector » Thread Tools Show Printable
Click View installed printers or fax printers. http://applecountry.net/error-code/dell-error-code-10.php ernest November 21, 2012 I have a dell machine,..AB are yellow and CD arr green and it cant display on the monitor what could be the problem,please help Dave November 21, Try replacing the network cable.These lights indicate there is network communcation:Green lightindicates a 10-Mbps network connection Orange lightindicates a 100-Mbps network connection Blinking amberindicates network traffic Restart the computer and try Posted by BigDaddyJinx on 30 Oct 2005 5:42 The diagnostic tree can be located here:
See "Drive Problems" for troubleshooting suggestions. Determine if a conflict exists by removing an expansion card (not a graphics card) and restarting the computer. Ensure that the port settings match the recommended settings. Source If it doesn't contact your technical support If it does add the memory modules back one at a time until the fault re-occurs, test that module in another slot and contact
Because the next money I spend will be a newand better computer. Dell Error Code 2000-0142 Power LED and Diagnostic LEDs Light Pattern Problem Description Suggested Resolution Diagnostic LEDs Power Button LED The computer is either turned off or not receiving power. Ensure that the sound is not muted by clicking any boxes that are checked.
If else, replace the motherboard. greengreengreengreenNormal operating condition after POSTNone. Go and check it out, you might land a code for a free game. Dell Error Codes 1 2 3 Replace the memory module(s) (see "Memory" for module installation procedures).
And YOU are the one who'll decide where to go...” ― Dr. Seuss, Oh, the Places You'll Go! 0 Feral That's what I do. If you are using a PS/2 mouse Enter system setup and ensure that Mouse Port under the Integrated Devices option is set to On. have a peek here Ensure that any power strips being used are plugged into an electrical outlet and are turned on.
From what I inspected non appear bloated at all. If identified the memory failed, replace the memory. Ensure that the device is turned on Firmly press the device's power button. Turn your computer off, unplug it, and remove all but one of the cards.