Figure 1-5. NIC Indicators 1 link indicator 2 activity indicator Table 1-5. NIC Indicator Codes Indicator Indicator Code Link and activity indicators are off The NIC is not connected to the E1710 I/O ChannelChk High BIOS has reported an I/O channel check. System reset POST E2018 ProgTimer High 0x88 -- Programmable interval timer error. By BBU do you mean UPS? have a peek at this web-site
Check screen for specific error messages. The fourth message displays as the standard overflow message. power supply fan failure or power supply over-temp). If the problem persists, see Getting Help. http://en.community.dell.com/support-forums/servers/f/956/t/18940287
Information only. See the Dell OpenManage Baseboard Management Controller User's Guide for information about these utilities. N/A Any N/A E141F N/A 0xC4–Dell remote access controller (DRAC) configuration failure.
Any E1311 RPM Fan Mod #B Low Same as above except for fan B of module #. Drive online Steady green. If the problem persists, see your RAID documentation. Dell Poweredge 1950 Error Codes Test CMOS battery by setting time, unplugging system for 1 hour, plugging system back into power source, turning it on, and checking time.
The system BIOS has reported a PCI system error on a component that resides in the specified slot. Dell Poweredge 2950 Error Codes I'm 99% sure they are in the same strip. N/A Any N/A SBIOS N/A 0x05– BIOS shadow into memory. http://www.admon.org/hardwares/dell-pe2950-lcd-message-explained/ Gate A20 failure Faulty keyboard controller; faulty system board.
Remote Access Controller initialization failure. I1911 – >3 Errs Chk Log on my 2950 server system. E1714 Unknown Err The system BIOS has determined that there has been an error in the system, but is unable to determine its origin. Ensure that only ECC FBD1 memory is used.
AC Cycle or SEL clear Any E1225 ESB 1.5VPwrGd High ESB1.5 VV voltage regulator has failed. The SYSTEM NAME displays under the following conditions: * The system is powered on. * The power is off and active POST errors are displayed. Dell Poweredge 2950 E1614 problem persists, see "Troubleshooting Power Supplies" on page 118. E161c Memory subsystem failure.
The following DIMM is electrically isolated: DIMM x. Check This Out Dell recommends purchasing memory upgrade kits directly from www.dell.com or your Dell sales agent to ensure compatibility. Check the time and date settings. That's fantastic media since it implies that dell error e1624 odds are very good your dilemma has been nicely reported and can more likely be fixed on your part! E1624 Lost Power Supply Redundancy. Check Psu Cables
Remove and reseat the PCI expansion cards. See Troubleshooting System Cooling Problems. If the problem persists, the riser card or system board is faulty. http://applecountry.net/error-code/dell-error-code-150.php E1710 I/O Channel Chk The system BIOS has reported an I/O channel check.
Check control panel LCD for additional scrolling messages. Poweredge 2900 Power Supply N/A Any N/A E122B N/A 0x00b0–Keyboard controller failure. Check the AC power source for the specified power supply.
See System Memory. This message is usually followed by specific information. Failing device is reseated/replaced/repaired. E171f Pcie Fatal Error Faulty or improperly installed diskette drive.
E171F - PCIE Fatal Err B## D## F## PCIE Fatal Err Slot # Causes: The system BIOS has reported a PCIe fatal error on a component that resides in PCI configuration System reset POST E201C SMI Init High 0x8C -- System management interrupt (SMI) initialization failure. Get 1:1 Help Now Advertise Here Enjoyed your answer? have a peek here Name (Required) Mail (will not be published) (Required) Website Admon websites are hosted by Linode.com Popular Latest Comments Tags Dell PE2950 LCD Message explained 16 Comments Update CentOS 4 to CentOS
E1614 PS # Status E1618 PS # Predictive E161C PS # Input Lost E1620 PS # Input Range Power source for specified power Check the AC power source for supply is See Troubleshooting System Cooling Problems. E1210 CMOSBatt Low CMOS battery is missing or the voltage is outside of the allowable range. Failing device is reseated/replaced/repaired.
The amount of system memory has changed Memory has been added or removed or a memory module may be faulty. Ensure that all pairs of memory modules are of the same type and size, and that they are properly installed.