Blinking Amber Initial state of light at power up.Indicates system has power, but the POWER_GOOD signal is not yet active.If the Hard Drive light is off, it is probable that the For additional safety best practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance. For additional safety best practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance. Symptom Tree Lists the most common symptoms encountered and allows you to select a test based on the symptom of the problem you are having. Source
Back to Top 5. If identified any of the component failed, replace the component. If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop, then shut down your computer and try again. If two or more memory modules are installed, remove the modules, then reinstall one module and restart the computer. http://www.dell.com/support/article/us/en/04/SLN284978/en
If multiple versions are listed, select the version appropriate for your computer. Power off computer, leaving the computer plugged in. Taal: Nederlands Contentlocatie: Nederland Beperkte modus: Uit Geschiedenis Help Laden... NOTE: The Extended Test periodically requires your input to answer specific questions.
Ensure that Microsoft® Windows® Recognizes the drive Windows XP: Click Start and click My Computer.Windows Vista: Click the Windows Vista Start button and click Computer.If the drive is not listed, Power LED and Diagnostic LEDs Light Pattern Problem Description Suggested Resolution Diagnostic LEDs Power Button LED The computer is either turned off or not receiving power. No idea what you would do if another memory module fails in the same slot though. Dell Error Beep Codes Determine if a conflict exists by removing an expansion card (not a graphics card) and restarting the computer.
If it doesn't contact your technical support If it does add the memory modules back one at a time until the fault re-occurs, test that module in another slot and contact Dell Error Codes 1 2 3 Hard-disk read failure Possible hard drive failure during hard-drive boot test (see Contacting Dell for assistance). But that is way out of my league.Mark Flag Permalink Reply This was helpful (0) Collapse - sticks by mike1773 / August 14, 2009 7:30 AM PDT In reply to: Other
In the Hardware Troubleshooter list, select the option that best describes the problem and click Next to follow the remaining troubleshooting steps.
BIOS may be corrupt or missing. Dell Laptop Error Codes If two or more memory modules are installed, remove the modules and then reinstall one module (see Memory). A possible processor failure has occurred. Run Express Test first to increase the possibility of tracing the problem quickly.
Posted by pmb2013 on 12 Jan 2014 13:49 UPDATE It was the power supply! http://www.tomshardware.com/forum/353746-28-dell-optiplex Bypass power strips, power extension cables, and other power protection devices to verify that the computer turns on properly. Dell Error Codes 1 3 4 If the operating system is attempting to boot from a device (such as the floppy drive or optical drive), check system setup to ensure the boot sequence is correct for the Dell Error Codes 3 4 Optiplex 755 Another failure has occurred.
Not enough memory or resources. this contact form If the computer starts normally, continue to install additional memory modules (one at a time) until you have identified a faulty module or reinstalled all modules without error. Click Properties® Tools® Check Now. If identified the storage failed, replace the storage. Dell Error Codes Lights
WeergavewachtrijWachtrijWeergavewachtrijWachtrij Alles verwijderenOntkoppelen Laden... Disconnect all internal and external peripherals, and restart the computer. If the problem persists, contact Dell (see Contacting Dell). 3 Possible system board failure. have a peek here If the floppy drive is your boot device, ensure that the cables are connected and that a bootable floppy disk is in the drive.If the hard drive is your boot device,
Viruses can sometimes prevent Windows from recognizing the drive. Dell Support Error Codes Don't think you ever mentioned the version of Windows on this system, but keep in mind that if it's XP, you'll have to change BIOS back to RAID Autodetect/ATA to run Ensure that the printer is turned on Check the printer cable connections See the printer documentation for cable connection information.Ensure that the printer cables are securely connected to the
Test the electrical outlet Ensure that the electrical outlet is working by testing it with another device, such as a lamp. Then shut down your computer and try again. Symptom Tree This option allows you to select tests based on a symptom of the problem you are having. Dell Error Code 2000-0142 NOTE: If you need technical assistance for your scanner, contact the scanner's manufacturer.
Log in om je mening te geven. Ensure that the processor power cable is securely connected to the system board power connector (POWER2) (see "System Board Components" section of the Service Manual for your computer).Remove and then reinstall Check the software documentation If necessary, uninstall and then reinstall the program. http://applecountry.net/error-code/dell-error-codes-ide.php Repeat with each module, inserting the previous and removing the next, till you find the defective one then replace it.
See the following: Mini Tower Heat Sink and Processor Desktop Heat Sink Assembly Small Form Factor Heat Sink and ProcessorUltra Small Form Factor Heat Sink and Processor If you require further assistance, please contact technical Support. If available, install verified working memory of the same type into your computer. Posted by pmb2013 on 14 Jan 2014 10:57 After running the Dell diagnostics it detected a bad boot drive so i know what the problem is now.
If your speakers have volume controls, adjust the volume, bass, or treble to eliminate distortion. Follow Us Facebook Twitter Help Community Forum Software by IP.BoardLicensed to: What the Tech Copyright © 2003- Geeks to Go, Inc. Volgende Optiplex 780 SFF Flashing Amber Power Light unable to start - Duur: 44:07. Memory modules are detected, but a memory failure has occurred.
The light remains solid or off to indicate different states: No light Indicates no power available for the power supply or the power supply is not working.Green light Indicates Steady Amber A possible coin cell battery failure has occurred. Try different settings for Color quality and Screen resolution. Clear CMOS.
When the test completes, record the test results and then press any key to return to the previous menu. NOTE: Write down any error codes and problem descriptions exactly as they appear and follow the instructions on the screen. For additional safety best practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance. A program is designed for an earlier Windows operating system Run the Program Compatibility Wizard Windows XP: The Program Compatibility Wizard configures a program so that it runs in
For additional safety best practices information, see the Regulatory Compliance Homepage on www.dell.com at www.dell.com/regulatory_compliance. Power Supply Diagnostic Light The power supply diagnostic light located on the back of the computer, near the power connector. At the Dell Diagnostics Main Menu, left-click with the mouse, or press