Test the dispenser by completing several test dispenses. A mechanical error has occurred. If these actions have no effect on dispenser operation, replace the dispenser mechanism and/or the note cassette. If the error code returns, replace the note transport module. this content
Make sure the shelf that the dispenser is mounted on is level and seated at all four corners. 3. Recommended Action: This error code occurs when the message received by the dispenser is incorrect. Error Code: 3 Description: BCD NOANSWER Possible Cause: Possible may be a processor or telephone hardware problem. Error Code: 65 Description: Processor not communicating with the modem correctly Possible Cause: This is normally a terminal problem. http://atmequipment.com/s.nl/it.I/id.18/.f
Access the error code command to determine if any sensors in the reject channel are dirty of defective. Error Code: 356(68)[h] Description: Error in note transport. Error Code: 108 (6Ch) Description: Unexpected note at double detect Recommended Action: A note has been detected in the double detect sensor without being detected at the width sensor first. 1.
Complete several live dispenses to ensure the dispenser is working correctly. Error Code: 148 Description: Write to electronic journal failed. If error persists, replace the dispenser mechanism. Atm Error Code 070 Error Code: 304(34h) Description: Rejected notes.
Error Code: 133 Description: +5 VDC not present on carrier detect. Diebold Atm Error Codes Error Code: 13 Description: BGD DONE GOOD Possible Cause: Communication was normal, but response header does not match request. It the error code repeats, verify the power supply output voltages are within expected values. Go Here If error persists, replace the dispenser mechanism.
Error Code: 140 Description: Time-out waiting for printer to be ready. Atm Response Code 072 Recommended Action: This error code will occur only in cash dispensers running ACS terminal software. Replace the modem module. Make sure the diverter is not jammed.
Error Code: 18 Description: OVERFLOW Possible Cause: Received more characters, than expected after request causing modem buffer overflow. https://atmtrader.com/errorCodes Make sure there are not any documents jammed at any of note feeder exit sensors. Diebold Status Codes Make sure the diverter moves freely. 4. Diebold Atm Troubleshooting Error Code: 158 Description: Format command to electronic journal failed.
All Rights Reserved. news Error Code: 145 Description: Error in reply from the electronic journal. Recommended Action: This error is usually associated with an empty note cassette or currency that is in “unfit” condition. 1. Recommended Action: This error code occurs when documents are requested from a cassette that is not present or is not open. Atm Error Codes
Reset the cash dispenser and clear the error. Verify that all access panels are closed and secured. Reset the cash dispenser and clear the error. have a peek at these guys Cassettes with no identity must be injected with a new cassette ID (See the 5000 Cash Dispenser Configuration Manual).
Remove the cassette and visually inspect for loose or disconnected connectors on both the upper and lower width sensor printed circuit boards. 3. Atm Error Code 3-da001 Error Code: 195 Description: Receipt printer out of paper. Inspect the cables connected to CN2, CN3, CN4, and CN5.
Open all access panels and inspect for jammed documents and other debris. Error Code: 14 Description: BGD DONE BAD Possible Cause: 1. Inspect for jammed currency at the Exit. Ncr Atm Error Codes This problem may be caused by a corrupt pin working key.
Clean the exit sensor using a soft brush and a vacuum cleaner. Recommended Action: This error may occur anytime that a cassette is removed from the cash dispenser with the AC Power ON. Make sure the access panel on the bottom of the note qualifier is closed and locked in position. check my blog Error Code: 161 Description: Electronic journal clear feature failed.
This is normally an internal terminal problem. Recommended Action: This status is generated if the double detect is unable to calibrate. Verify the blue lever on the left side of the printer in the print position. If the error persists, replace the dispenser.
If the problem persists, remove the main board and replace the modem. If the error clears, put the cash dispenser in service. Inspect the exit area to ensure nothing is blocking the exit sensor. Recommended Action: This error is produced when a sensor in note transport module is not working correctly during an internal self-test preceding the movement commands.
Clear the jammed documents. 2. Error Code: 105 (69h) Description: Insufficient notes to learn from Recommended Action: There may be an insufficient number of notes in the cassette to complete the requested “learn note thickness” command. If the operation is normal, you may put the cash dispenser in service. If the error clears, put the cash dispenser in service. 5.
Error Code: 139 Description: Printer controller not responding to commands. Inspect for jammed currency at the Diverter. 800.498.5795 New! Make sure the tamper screw is secure to the SPED module.
Replace the dispensing mechanism. Click here follow the steps to fix Diebold Error Codes and related errors. If these actions have no effect on dispenser operation, replace the dispenser mechanism. Baud rate set to high for telephone line conditions.
If these actions have no effect on dispenser operation, replace the dispenser mechanism. Recommended Action: See the recommended action for error code 144. Recommended Action: Enter management functions and enter the pin master key. The reason that the error code is generated is the detection of an incorrect LRC character or a parity error.